Threadless Tribal Disk With Chains Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Tribal V With 3 Dangle Heart Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Triforce Attachment

• Size: 6mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Trio Ball Attachment

Ball: 2mm x 3

Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Trio Diamond Shape Fan Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Trio Marquise Attachment

• Size: 8.2mm x 3.4mm

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Triplet Jeweled Spike Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless Turtle Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Threadless White Fire Opal And Crystal Prong Set Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136) 

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Titanium Cable Chain 

Sizes: 20mm  /  30mm  / 40mm

O-Ring: 2mm 

Trident Titanium Jeweled Hinged Rainbow Ring

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Titanium Twist Chain

Sizes: 20mm  /  30mm  / 40mm

O-Ring: 2mm 

Trident Curve Ball Nose Stud - Pig Tail

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Curve Nose Stud Disc - Pig Tail

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Double Suede Gift Pouch 

L - 66mm   W - 55mm  

Trident Draw Gift Box Drawer                                                                                                 

Indulge in the exquisite texture of this meticulously wrapped gift box, adorned with delicately woven paper. The interior showcases a luxurious velvet design, ensuring a touch of opulence. An elastic band thoughtfully secures Naval bars, hinged rings, and more, while the plush velvet foam insert cradles your precious items such as posts and ends with care.

Embodying elegance, the box is embellished with a captivating logo in shimmering silver foil, adding a touch of sophistication and allure. 

L - 61mm   W - 51mm   H - 30mm

Trident Gift Box

Indulge in the exquisite texture of this meticulously wrapped gift box, adorned with delicately woven paper. The interior showcases a luxurious velvet design, ensuring a touch of opulence. An elastic band thoughtfully secures Naval bars, hinged rings, and more, while the plush velvet foam insert cradles your precious items such as posts and ends with care.

Embodying elegance, the box is embellished with a captivating logo in shimmering gold foil, adding a touch of sophistication and allure

L - 50mm   W - 50mm   H - 35mm

Trident Jeweled Curve Nose Stud - Pig Tail

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Jeweled Prong Set Nose Stud

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Trident Microfiber Showcase Display Tray

Size: 20cm L x 15cm W x 3cm H

Trident Sterile Needle Blades

Ethylene oxide (EO) Gas Sterilized Packs of 50pcs  - Length 48mm

Trident needle blades offer the highest sharpened needles to insure minimal trauma to the skin. Made out of Surgical Steel these needles are hollowed to allow a cleaner insertion. 

Each Needle is separately packaged in sterile blister pack. 

Smooth, Precise & Sharp.

Trident Titanium Cable Chain Double

Size: 30mm 

O-Ring: 2mm

Trident Titanium Threadless Cluster 2.5mm Crystal

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Crescent Jewel Moon

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Heart Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Jewel Eye

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Nose Labret 1.0mm x 8mm x 2.5mm Crystal 

Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Nose Labret 1.0mm x 8mm x 2.5mm Disk

Threadless Titanium Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Prong Set Crystal Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Side Facing Crystal Attachment

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.

Trident Titanium Threadless Side Facing Opal Attachments

Manufactured out of Implant Grade Titanium (Ti-6AL-4V-ELI ASTM F136)

Threadless Jewelry Method:

Threadless jewelry is tensioned by using the end of the attachment and bending it within the bar to hold into place. To create the tension insert the pin on the end of the attachment slightly into the bar and bend slightly. Once inserted into the bar the bend in the pin should create the tension needed to hold into place. Direction below:

1. Insert the pin on the end of the attachment 1/4 - 1/3 into the bar. (Labret, barbell etc.)
2. Slightly bend the insertion pin within the bar.
3. Push the end into the shaft and test the fit.

Insuring the fit: Insure the attachment is held in place and is tight. Adjust as necessary, if the pin does not hold tight enough redo the steps & create more tension.